COMPATIBILITY FIRST · NO INTRO ADS
Replace a pull-down faucet hose
Fit the 150259 hose on the matching manual Moen Arbor 7594C version.
Illustrated version: Manual Moen Arbor 7594C version using hose 150259, a white quick-connect with a black release button, and a snap-on hose weight. Check applicability ↓
Read the narration transcript
Replace a split pull-down hose with the model-matched part. This manual Moen Arbor 7594C example uses hose 150259, a white quick-connect with a black button, and a snap-on weight. Close both supplies. Open the faucet through hot and cold and verify no flow. Stop for failed shutoffs, severe corrosion, or moving pipe, and call a plumber. Place a bowl underneath. Unclip the weight. Hold the white connector, press and hold its black button, and pull the hose end straight out. Pull the old hose up through the spout. Hold its coupling steady and unscrew the spray head. Clean and inspect the screen washer and O-ring; replace damaged seals. Seat them correctly, then attach the new hose to the head without overtightening. Feed the small end down through the spout and remove its protective cap. Push it into the connector until it clicks, then tug-test. Snap the weight onto the spray-head side a few inches above the loop’s bottom. Confirm free travel. Restore water slowly. Test both spray modes, extension and retraction, and inspect both connections.
01 / MATCH YOUR DESIGN
Confirm this is your version.
- Manual Moen Arbor 7594C version using hose 150259, a white quick-connect with a black release button, and a snap-on hose weight.
- Confirm the actual connector, hose part number and version first. The 7594 parts sheet also lists older hose/connection variants; this sequence does not apply to every 7594 faucet.
- Inspect the spray-head screen washer and O-ring, remove the new hose's protective cap before connection, and perform a separate tug test after the click.
- The weight sits on the moving spray-head side a few inches above the loop bottom, with clear travel. Keep the loop free of stored items and plumbing.
- Follow any hose-weight locator mark supplied for the exact hose. The illustrated placement is approximate and must allow free travel.
Representative educational geometry, not manufacturer CAD or certification. Use the instructions supplied with your exact fixture and replacement part.
02 / CHECK BEFORE BUYING
Find the source of the problem.
- Locate the leak before buying: distinguish a split hose from a loose spray-head union, damaged seal, supply leak or faucet-body leak.
- A retraction problem alone may be an obstructed loop or misplaced weight. Inspect that before replacing a sound hose.
03 / PARTS & PREPARATION
Have the right tools ready.
- Confirmed Moen 150259 replacement hose for the installed version
- Correct matching spray-head seals if damaged
- Bowl, towels, flashlight and a gentle hand-tool counterhold if needed
These checks are for your use. They do not certify compatibility and are not saved.
04 / THE PROCEDURE
Work through the repair.
- Identify the model-matched hose. Replace a split pull-down hose with the model-matched part. This manual Moen Arbor 7594C example uses hose 150259, a white quick-connect with a black button, and a snap-on weight.
- Isolate and verify no flow. Close both supplies. Open the faucet through hot and cold and verify no flow. Stop for failed shutoffs, severe corrosion, or moving pipe, and call a plumber. Place a bowl underneath.
- Release and remove the hose. Unclip the weight. Hold the white connector, press and hold its black button, and pull the hose end straight out. Pull the old hose up through the spout. Hold its coupling steady and unscrew the spray head.
- Inspect seals and fit the hose. Clean and inspect the screen washer and O-ring; replace damaged seals. Seat them correctly, then attach the new hose to the head without overtightening. Feed the small end down through the spout and remove its protective cap.
- Click, tug-test and position weight. Push it into the connector until it clicks, then tug-test. Snap the weight onto the spray-head side a few inches above the loop’s bottom. Confirm free travel.
- Test spray modes and retraction. Restore water slowly. Test both spray modes, extension and retraction, and inspect both connections.
05 / VERIFY THE RESULT
Test operation and check for leaks.
- Restore both supplies slowly; test both spray modes and hot/cold operation.
- Extend and retract the hose through its full intended travel without snagging.
- Check the head connection and under-sink quick-connect while running and at rest.
KNOW YOUR LIMITS
Stop and get qualified help when…
- Either shutoff fails; flow or pressure remains
- Severe corrosion, moving pipework or a damaged quick-connect
- Connector or weight differs from the illustrated version
- The new connector fails the tug test, hose travel binds, or leakage remains
Use your actual parts prices, tool costs and an all-in local service quote when deciding. A cheaper repair is not worth unsafe isolation or water damage.
Opens Google Maps in a new tab. Check the search area, or add your city or ZIP code.
MANUFACTURER REFERENCES
Sources & scope.
The references below support the named example. Their instructions and version notes take priority if your fixture differs.
- Moen Arbor 7594 exploded parts view and older-version notes
- Moen quick-connect identification and removal
- Moen 150259/202750/212650 hose installation
- Moen hose-weight positioning
- Moen installation sheet INS2049: hose-weight guidance
Checked October 15, 2026. Information links only. No affiliate links or parts sales.